HOT ! Classic｜Eco-Poxi｜ Other Products

Eco-Poxi

Available Sizes

1.5 Gallon BAG-PAKTM Unit in a single pail.
3 Gallon BAG-PAKTM Unit in a single pail.
15 Gallon Unit in three 5-gallon pails

Advantages

100% solids
Good hardness and abrasion resistance
Cost-effective
Multi-functional. Can be used as a primer, body coat, grout coat or binder resin
Low viscosity for easy flow and self-leveling characteristics
Fast cure time
VOC compliant

Description
ECO-POXI is a cost effective, 2-component, 100% solids amber/clear epoxy body and basecoat material. ECO-POXI is a VOC compliant material that meets all of the USDA/FDA guidelines for use in federally inspected facilities.
Uses
ECO-POXI is ideal when the durability of a 100% solids epoxy is required, but UV and chemical resistance are not necessary. Its low viscosity makes ECO-POXI an excellent "seed" coat for broadcast systems, an excellent grout coating over troweled mortar systems and an excellent binder resin when combined with fine aggregates to create self-leveling slurry patching mixes. ECO-POXI is not recommended as a finish coat as it has low color stability and low chemical resistance.
Typical Coverage
ECO-POXI is typically applied between 60-160 square feet per gallon per coat depending upon substrate and project requirements.
Physical Properties

Volume mix ratio
2 to 1 (Resin to Hardener)

Viscosity (mixed)
300 - 500 CPS Typical

Solids Content (%)
100 % (ASTM D-2697)

VOC
Meets all US Regulations

Application Temps.
60° – 85° F (10° – 29° C)

Hardness (ASTM D-2240)
60-70 (Shore D)

Gel Time
12-20 minutes @ 75° F

Dry to Touch (recoat with compatible products)
2.5 - 4 hours @ 75° F

Through Cure
4-8 hours @ 75° F

Open for light traffic
24 hours @ 75° F

Limitations & For Best Results

Do not thin this product.
Do not apply when Humidity exceeds 70% indoors.
Do not allow to puddle during application.
Allow each coat to dry to 'tack-free' or clear prior to re-coat.
When re-coating, always apply the next coat within 24 hours of completing the previous coat.

Do not apply less than 10 mils per coat as separation may result.
When pigmenting this product using lighter colors two 10-12 mil coats may be required for full hide.
Do not use a finish coat where color stability or chemical resistance are required.

Product Application
Apply using brush, roller and squeegee ROCK-TRED product test data is based on environmental temperatures of 75° F (24° C). Viscosity and working time are always affected by temperatures above or below that mark. When applying product always consider the ambient, surface, and product temperature at the time and place of installation.
Color and Textures
ECO-POXI is manufactured in amber/clear and can be field pigmented using ROCK-TRED colorants. Most ROCK-TRED products are available in a wide range of textures using an appropriate aggregate.
Chemical Resistance
Always refer to ROCK-TRED's chemical resistance chart for specific information on each product / system or contact ROCK-TRED directly.
Product Storage
DO NOT allow ROCK-TRED products to freeze. All ROCK-TRED products should be properly stored above the floor on pallets or shelves, and in an area that has a constant minimum temperature of 50°F.
Surface Preparation
Always apply ROCK-TRED products to a clean / sound substrate that is free of laitance, grease, oils, debris, and curing compounds. Concrete substrates should be cured for a minimum of 28 days prior to application of product [except as otherwise noted on the individual Product Data Sheet]. Whenever possible, remove existing coatings and/or flooring systems completely; if complete removal is not possible always perform tests to determine adhesion and compatibility to the existing flooring. Mechanical preparation by means of a shotblasting or diamond grinding machine to a minimum CSP-2 profile followed by application of an appropriate ROCK-TRED primer or base system is the best and recommended installation method for ECO-POXI applications. If the substrate is not properly prepared and the appropriate profile is not achieved, failure of the product to adhere to the substrate may occur.
Clean Up
Application tools and equipment can be cleaned with soap and water immediately after use, or with solvent once the product has begun to cure.
Disposal
Product containers will contain product residue and must be disposed of properly. Label warnings must be observed at all times. All containers must be disposed in accordance with federal, state, and local regulations.
Important Notice
Always read and acquaint yourself with ROCK-TRED's Product Data Sheet, SDS [safety data sheet], and product labels for each individual product prior to mixing and prior to use. For further assistance, product questions, additional information and/or unexpected or unusual installation conditions – contact your Area Sales Representative or ROCK-TRED directly for recommendations. Kit components are pre-measured for optimal performance. Catalyzation errors due to incorrect mixing in the field voids product warranty.
Brand:Rock TredSKU:12815Tags:Clear Epoxy, Rock TredSize:1.5 Gallons, 3 Gallons, 15 Gallons